How to fix an oven that won’t heat: A DIY guide to settings and thermostats

4

The oven is quiet. Or it warms up, but the cookies on the bottom shelf are charred, but the cookies on the top shelf are still raw. Look at a blank digital display or a rotating heating element and wonder if you need to call a professional. Stop. Before you panic about repair costs, consider that the problem could be a simple control error or your thermostat may not be working properly. Most of these problems are cheap and easy to fix yourself. No electrical engineering degree required. All you need is a screwdriver, a little patience and the right mindset.

Replace the oven settings control

If the oven refuses to heat, the setting controls are usually the culprit. This is the switch that tells the oven to turn on. If you fail, the oven will stay cold. Replace it with:

First, pull the adjustment knob straight off the shaft. If it is stuck, turn it a little. You may need pliers with padded jaws to avoid damaging the plastic, but it just pops off. Next, we need to uncover the mechanism. This usually means removing the rear service panel or the entire front panel. Remove any other knobs in the way. The setting control is located right behind the knob and is held in place by two screws. Unscrew them and remove the device.

Now this is a tip that is left out of most guides. There’s no need to bother using a volt-ohm-milliamp meter (VOM) to test old controls. The results are rarely convincing. Mechanical switches wear more than a multimeter can consistently detect. If the control is bad, it’s best to replace it. Get new controls designed specifically for your oven model. It’s a small part, but it makes a big difference.

Disconnect the wires from the connectors of the faulty device. Note the direction of each wire. If you have a bad memory, take a picture. Remove bad controls. Connect the new one with the exact same configuration. Put it back in place. Tighten the screws. Put the knob back. If the oven heats up, you just saved yourself a service call.

Calibration and testing of the oven thermostat

Uneven heating? The oven may be too hot or not heated enough. It refers to the thermostat. Before we start tearing it down, we need to know if it’s really broken or just out of sync.

Get the oven thermometer ready. Place it in the center rack. Set the oven to a standard range (like 350 degrees Fahrenheit). Let it run for about 20 minutes. Check your thermometer. If your readings are off by 25 degrees Fahrenheit (high or low), your thermostat needs to be calibrated.

Adjustments can usually be made without buying new parts. Remove the thermostat knob from the control panel. Behind it is a round, notched plate, which is fixed with two screws. Unscrew thems just enough to allow the disc to rotate, but do not remove them. Rotate the disc with a screwdriver. For every 8 counterclockwise rotations, the temperature rises by about 25 degrees. Count it by turning it clockwise.

Some models use different methods. Look inside the shaft of the adjustment knob. There may be a screw hole. Place the screwdriver in place and turn it counterclockwise to raise the heat. Small adjustments are important again. 1/8 of a turn is a normal increment. Retest the oven after each adjustment.

Testing a faulty thermostat

Does calibration solve the problem? Your thermostat may be broken. Tested with a multimeter.

Place the VOM on the RX1 scale. You need to use the thermostat located behind the control knob. You can access it by removing the rear maintenance panel. Locate the thermostat connectors.

Disconnect one wire from the connector. This separates the components. Attach one of the multimeter probes to each terminal of the thermostat. If the thermostat is working, the resistance of the meter should be zero. If the pointer jumps to a higher reading, the circuit is open. The thermostat is faulty. It needs to be replaced.

Install a new thermostat

If the test shows a failure, you need a new thermostat. Make sure it’s the same type as the old one. Incompatible parts can cause safety risks or not work at all.

Disconnect the connector wires from the old thermostat. Pull off the control knob. Remove the fixing screws. In some ovens, you will notice that a wire runs from the thermostat to the oven cavity. It is connected to a sensing bulb that monitors the actual temperature inside. The lamp usually stays in place with a bracket. Remove the bracket to release the bulb. Carefully pull the wires, bulb and old thermostat out. Handle the bulb with care; puncture it will ruin the calibration.

To install a new thermostat, use the reverse procedure. Reinstall the sensor bulb and bracket. Put the wires back in place. Fix the thermostat with screws. Reconnect the connector wires. Put the knob back. Tighten the front panel.

Turn on the oven. Is it hot? Can it maintain temperature? If yes, then you have done it. If the oven is still acting strange, there may be a problem with the heating element or ignition system. But for most homeowners, fixing a controller or adjusting a thermostat is the entire battle. Your kitchen is back. And you don’t have to wait for technician who charges by the hour. The tools are simple. The steps are simple. As a result, your oven works and your wallet is a little lighter than it would have been otherwise. Be sure to check these wire connections. One loose wire can mean the difference between a perfect roast and a cold meal.