Sandpaper is basically a mechanical saw. Cut the material using the sharp serrated edges glued to the base. Whether you are working with wood, metal or plastic, the abrasive particles are attached to a substrate such as kraft paper using a special adhesive. The magic happens in the grit.
The roughness number tells you exactly what kind of cut to expect. Measure the density of these sharp particles per square inch. Smaller numbers mean fewer, larger and more aggressive teeth. The higher the number, the more teeth there are, the smaller and thinner they are. This distinction is important. Using the wrong grit can ruin your finish or sandpaper in seconds.
Understanding coating density
Before picking a grit, look at how the abrasive is applied. This is called coating.
Open Coat The sandpaper has gaps between the sanding grains. Why is this important? Because sawdust and sludge can remain inside the abrasive. Open pores allow debris to fall off or remain on the surface without clogging it. Sandpaper cuts last longer.
Closed-coated A dense layer of sandpaper. There are no gaps. It cuts quickly at first, but clogs quickly when removing large amounts of material. It is better for final smoothing than heavy stripping.
Industrial sandpaper typically uses better quality substrates and adhesives than those sold in regular hardware stores. It lasts a long time even under heavy load. But for most DIYers, understanding the grit scale is the most important skill.
Choosing the Right Sandpaper Grit for your work
Numbers cannot be picked out of thin air. The roughness varies depending on the condition of the surface and the desired result.
If you want to remove old varnish, remove bad scratches or smooth warped boards, you need coarse sandpaper. Look for a grit of 40-60 grit. These grits dig deep. Removes material quickly. This can leave deep scars that need to be addressed later.
Use medium sandpaper to smooth the surface, fill in deep scratches and remove small irregularities. The particle size is typically 80 and 120 grit. It is the workhorse range for most woodworking projects. Balances material removal and surface grinding.
When you’re ready to finish, switch to very fine sandpaper. Grits from 400 to 600 are for final smoothing. Remove any remaining scratches with a medium-sized emery stone. Prepare the surface for stain, paint or varnish.
The “Going Through the Grits” Rule
The golden rules of sanding are: you almost always need to go through the grits.
You can’t jump straight from 40 grit to 400 grit. The 40-grit leaves deep and wide scratches. 400 grit is too fine to effectively remove these scratches. It will just burnish over them and makes them visible in the light.
You need to step up progressively.
1. Start with the coarse sand you need to remove old paint or smooth the wood.
2. Move to the next grit up. This will remove the scratches made in the previous step.
3. Repeat this process until you reach the final fine grit.
Each step removes traces of the previous step. If you skip one step, you can spend hours removing a scratch, but a single sheet of the missing grit can be removed in minutes.
Type of abrasive material
Not all abrasive particles are the same. The material affects durability, cutting speed and surface finish.
- Aluminum Oxide: This is most common in woodworking. It is durable and has self-regenerating properties. As the sharp edge wears away, the particles break up and a new sharp edge is formed. Lasts longer than most other types.
- Garnet: A natural mineral that wears out quickly. It gives a very smooth surface, which is why some carpenters prefer it for final polishing. However, it can quickly become clogged and dulls fast.
- Silicon Carbide: Very hard. Ideal for non-wood materials such as metal, plastic and fiberglass. Also used for wet sanding. Achieves efficient cutting even on hard surfaces.
- Alumina Zirconia: A very durable synthetic abrasive. It is especially used for cutting hardwood and metals. Keeps the edges longer even under heavy pressure.
General particle sizes and uses
The scale varies from very coarse to very fine. You can refer to the most common numbers as follows:
60 Grit: Ideal for heavy stripping. Use to remove old paint or smooth rough wood. Leaves visible scratches on the surface.
100 grit size (medium): Universal grit. Suitable for sanded wood before staining. Usually used after 60 grit to remove the deepest scratches.
220 Grit (Fine): This is an important intermediate step. If you apply several layers of paint or varnish, you need to sand between layers. 220 grit removes dust particles and rough areas without removing too much finish. Also suitable for final sanding before applying clear varnish to the interior wood.
400 Grit (Very Fine): Very fine. It is used for final sanding of the wood to achieve a glassy smoothness before applying a finish. They
